WS-9006U
Wireless Temperature Station
Instruction Manual
ption
tor
Outdoor
Temperature
Time
oor
erature
MIN/MAX/+ Button
Outdoor
Temperature
Sensor TX43U
CF / SET Button
FEATURES:
Four digit time display
12-hour or 24-hour selectable time
Indoor temperature (°F or °C)
Outdoor temperature (°F or °C)
Minimum and Maximum temperature
Four level RF strength indicator
Wall hanging or free standing
Low battery indicator for receiver and transmitter
100 foot wireless transmission range (open air)
SET TIME:
12/24-HOUR TIME: Hold the CF/SET button until 12hr or 24hr flashes in the lower
right hand corner. Press and release the MIX/MAX/+ button to switch between 12-hour
and 24-hour time. Press the CF/SET button once to continue.
HOUR: The Hour will flash. Press and release the MIX/MAX/+ button to change the
hour. Press the CF/SET button once to continue.
MINUTES: The minutes will flash. Press and release the MIX/MAX/+ button to change
the minutes.
NOTE: Hold the MIX/MAX/+ button to move quickly through the numbers. Press
CF/SET once to confirm and exit.
TEMPERATURE SELECTION:
FAHRENHEIT/CELSIUS: Press and release the CF/SET button once to switch from Fahrenheit to
Celsius.
FOUR LEVEL RF INDICATORS: The temperature station will indicate strength of signal
reception from the outdoor transmitter by the number of bars on the RF
indicator icon.
4-bars: Shows after initial set up and stays when reception is at full strength.
3-bars: Indicates one reception failure from the outdoor transmitter.
2-bars: Indicates two reception failures from the outdoor transmitter.
1-bar: Indicates three reception failures from the outdoor transmitter.
0-bars: Indicates four reception failures from the outdoor transmitter.
The antenna symbol will flash on initial set while searching for the signal. If it fails to receive a signal after
63 minutes the temperature station will display dashes (“--.-“). The temperature station will search again
for a signal for 3 minutes every next hour.
MIN/MAX RECORDING:
VIEW MIN/MAX: Press the MIN/MAX/+ button view indoor and outdoor MAX, MIN and Current
temperature.
RESET MIN/MAX: Hold the MIN/MAX/+ button for 3 seconds to reset all MIN/MAX readings to current
temperatures.
OUTDOOR TRANSMITTER RESET BUTTON:
The Temperature Transmitter has a RESET button. Use a small pointed object to gently press and
release to send a signal. Follow the instructions for in SET UP regarding the display.
NOTE: Removing power from the transmitter and display negates the need for the RESET button.
POSITIONING THE TEMPERATURE STATION:
Stand the Temperature Station on a tabletop, counter or desk, or mount on a wall. Ensure that the
Temperature Station continuously receives the 433MHz signal from the Sensor before mounting it in the
desired location.
WALL MOUNT
Install a mounting screw (not included) into a wall—leaving approximately 3/16 of an
inch (5mm) extended from the wall.
Place the Temperature Station onto the screw, using the hanging hole on the
backside. Gently pull the Temperature Station down to lock into place.
NOTE: Always ensure that the Temperature Station locks onto the screw before
releasing the station.
TABLE STAND: The Temperature Station has a wide base to stand on a desk or table.
POSITIONING THE REMOTE TEMPERATURE TRANSMITTER:
Wall mount using the hole on the back of the sensor. Best location is under the eave (12-18 inches) on
the North side of the home.
WALL MOUNT:
1. Install a mounting screw (not included) into a wall—leaving approximately 3/16 of an
inch (5mm) extended from the wall.
2. Place the temperature transmitter onto the screw, using the hanging hole on the
backside. Gently pull the transmitter down to lock into place
NOTE: Always ensure that the transmitter locks onto the screw before releasing.
TABLE STAND: Not recommended as the transmitter may be blown over and
damaged.
NOTE: The mounting surface can affect the transmission range. If, for instance, the transmitter is
attached to a piece of metal, it may reduce the transmitting range. For this reason, we recommend not to
place the unit on any metal surfaces or in any position where a large metal or highly polished surface is in
the immediate vicinity (garage doors, double-glazing, etc.). Before securing in place, please ensure that
the Temperature Station can receive the 433MHz signal from the temperature transmitter at the positions
that you wish to place them.
Place the remote temperature transmitter outside in a dry, shaded area. The remote temperature
transmitter has a range of 100 feet (30 meters). Keep in mind this distance is in open air with no
obstructions and that radio waves DO NOT curve to go around objects. Real-world transmission range
will vary depending on what is in the path of the signal. Each obstruction (roof, walls, floors, ceilings,
thick trees, etc.) will effectively cut signal range in half.
MAINTENANCE:
Keep the temperature station in a dry place.
Do not expose the display to extreme temperatures, vibration or shock.
Clean it with a soft damp cloth. Do not use solvents or scouring agents.
If the unit does not work properly, change the battery.
Do Not Mix Old and New Batteries
Do Not Mix Alkaline, Standard, or Rechargeable Batteries
SPECIFICATIONS:
Indoor Temperature:
Range:
Resolution:
Interval:
32° F to 122° F (0° C to 50° C)
1° F/C
57 seconds
Outdoor Temperature:
Range:
-22° F to 140° F (-30° C to -60° C)
Resolution:
Interval:
1° F/C
57 seconds
Power:
Receiver:
Transmitter:
2-AAA, IEC, LR3 alkaline batteries.
2-AA, IEC, LR6 alkaline batteries.
Dimensions:
Receiver:
Transmitter:
2 ½” W x 1” D x 3 ¾” H
1 ¾” W x 1” D x 4” H
WARRANTY INFORMATION
La Crosse Technology, Ltd provides a 1-year limited warranty on this product against manufacturing
defects in materials and workmanship.
This limited warranty begins on the original date of purchase, is valid only on products purchased and
used in North America and only to the original purchaser of this product. To receive warranty service, the
purchaser must contact La Crosse Technology, Ltd for problem determination and service
procedures. Warranty service can only be performed by a La Crosse Technology, Ltd authorized service
center. The original dated bill of sale must be presented upon request as proof of purchase to La Crosse
Technology, Ltd or La Crosse Technology, Ltd’s authorized service center.
La Crosse Technology, Ltd will repair or replace this product, at our option and at no charge as stipulated
herein, with new or reconditioned parts or products if found to be defective during the limited warranty
period specified above. All replaced parts and products become the property of La Crosse Technology,
Ltd and must be returned to La Crosse Technology, Ltd.
Replacement parts and products assume the remaining original warranty, or ninety (90) days, whichever
is longer. La Crosse Technology, Ltd will pay all expenses for labor and materials for all repairs covered
by this warranty. If necessary repairs are not covered by this warranty, or if a product is examined which
is not in need or repair, you will be charged for the repairs or examination.
The owner must pay any shipping charges incurred in getting your La Crosse Technology, Ltd product to
a La Crosse Technology, Ltd authorized service center.
Your La Crosse Technology, Ltd warranty covers all defects in material and workmanship with the
following specified exceptions: (1) damage caused by accident, unreasonable use or neglect (including
the lack of reasonable and necessary maintenance); (2) damage occurring during shipment (claims must
be presented to the carrier); (3) damage to, or deterioration of, any accessory or decorative surface; (4)
damage resulting from failure to follow instructions contained in your owner’s manual; (5) damage
resulting from the performance of repairs or alterations by someone other than an authorized La Crosse
Technology, Ltd authorized service center; (6) units used for other than home use (7) applications and
uses that this product was not intended or (8) the products inability to receive a signal due to any source
of interference.
This warranty covers only actual defects within the product itself, and does not cover the cost of
installation or removal from a fixed installation, normal set-up or adjustments, claims based on
misrepresentation by the seller or performance variations resulting from installation-related
circumstances.
LA CROSSE TECHNOLOGY, LTD WILL NOT ASSUME LIABILITY FOR INCIDENTAL,
CONSEQUENTIAL, PUNITIVE, OR OTHER SIMILAR DAMAGES ASSOCIATED WITH THE
OPERATION OR MALFUNCTION OF THIS PRODUCT. THIS PRODUCT IS NOT TO BE USED FOR
MEDICAL PURPOSES OR FOR PUBLIC INFORMATION. THIS PRODUCT IS NOT A TOY. KEEP OUT
OF CHILDREN’S REACH.
This warranty gives you specific legal rights. You may also have other rights specific to your
State. Some States do no allow the exclusion of consequential or incidental damages therefore the
above exclusion of limitation may not apply to you.
For warranty work, technical support, or information contact:
La Crosse Technology
2817 Losey Blvd. S.
La Crosse, WI 54601
Online product support is available at:
Contact Support: 1-608-782-1610
Product Registration:
FCC ID: OMO-M-13 (transmitter)
FCC DISCLAIMER
Statement according to FCC part 15.19:
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) this device may not cause harmful interference, and (2) this device must accept any interference
received, including interference that may cause undesired operation.
Statement according to FCC part 15.21:
Modifications not expressly approved by this company could void the user's authority to operate the
equipment.
Statement according to FCC part 15.105:
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against
harmful interference in a residential installation. This equipment generates uses and can radiate radio
frequency energy and, if not installed and used in accordance with the instructions, may cause harmful
interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment
does cause harmful interference to radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the interference by one or more of the
following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
Consult the dealer or an experienced radio/TV technician for help.
All rights reserved. This handbook must not be reproduced in any form, even in excerpts, or duplicated or
processed using electronic, mechanical or chemical procedures without written permission of the
publisher.
This handbook may contain mistakes and printing errors. The information in this handbook is regularly
checked and corrections made in the next issue. We accept no liability for technical mistakes or printing
errors, or their consequences.
All trademarks and patents are acknowledged.
|