Linear Satellite Radio DXS 32 User Manual

PRODUCT DESCRIPTION  
The DXS-32 is a battery powered stationary transmitter designed for use with Linear’s DXS and DX  
format receivers. This transmitter can be used in a variety of wireless remote control applications.  
Triggering the transmitter with its built-in magnetic switch sends a digitally coded wireless signal to  
its companion receiver.  
The digital DXS code format features over a million possible codes. The DXS transmitters are  
precoded at the factory to unique codes, so no field coding is required. The DXS-32 can send four  
different codes: alarm, restore, low battery and status.  
DXS-32  
BY  
MINIATURE  
Receivers must be programmed to the transmitter’s code before system testing and operation. Refer  
to the receiver’s instructions for details on programming.  
SUPERVISED  
DOOR/WINDOW  
TRANSMITTER  
In a typical installation, the magnet is mounted on a door or window and the transmitter is mounted  
on the frame. When the magnet moves more than 1/2" away from the transmitter, an alarm signal is  
sent. When the magnet returns next to the unit, a restore signal is sent. The magnet is adjustable  
with four height positions. A 1/4" high magnet spacer is also supplied to snap on to the base of the  
magnet.  
The transmitter is powered from two 3-Volt #2032 lithium batteries with an expected battery life of  
up to 4 years. Every hour, the DXS-32 will send a status transmission to the receiver. The hourly  
signal updates the receiver to the transmitter’s condition. By monitoring status transmissions, the  
receiver can determine if a transmitter has a low battery or has been removed from the system.DXS  
format receivers can monitor status signals, DX format receivers cannot.  
Installation Instructions  
Normally, the transmitter sends an exit/entry delay transmission code. Cutting an internal jumper  
selects an instant transmission code. Cutting this jumper doesn’t change the time of the actual  
transmissions, but changes the code of the signal sent so the receiver can determine the transmitter’s  
function.  
(760) 438-7000 • FAX (760) 438-7043  
USA & Canada (800) 421-1587 & (800) 392-0123  
Toll Free FAX (800) 468-1340  
DXS-32 FEATURES & ACCESSORIES  
OPENING CASE  
MAGNET  
ALIGNMENT  
MARKS  
REMOVE THE CASE TOP BY TWISTING A  
SMALL FLAT BLADE SCREWDRIVER IN  
TRANSMITTER  
THE SLOT ON EITHER END OF THE TRANSMITTER  
MAGNET  
SIDE  
MARK  
MAGNET  
ALIGNMENT  
MARKS  
TRANSMITTER  
SCREWS AND  
DOUBLE STICK TAPE  
MAGNET CAN BE MOUNTED UP TO  
1/2" FROM LEFT SIDE OF  
TWIST  
TRANSMITTER  
ADJUSTABLE  
MAGNET  
MAGNET  
ADJUSTMENT  
TAB (EACH SIDE)  
MAGNET  
SCREWS AND  
DOUBLE STICK TAPE  
SQUEEZE MAGNET TABS TO  
ADJUST MAGNET HEIGHT (4 POSITIONS)  
REMOVE BATTERY PROTECTION STRIP  
COMPONENT LOCATIONS  
ANTENNA  
TWO TYPE 2032  
BATTERIES  
PULL OUT & DISCARD  
BATTERY PROTECTION  
STRIP TO ACTIVATE  
TRANSMITTER  
DELAY/INSTANT JUMPER  
(CUT JUMPER FOR INSTANT)  
 

Kyocera All in One Printer FS 920 User Manual
Kyocera Printer FS 1010 User Manual
Leica Binoculars BL 42 User Manual
Lenovo Tablet Y470 User Manual
LG Electronics Air Conditioner LP121CEM Y8 User Manual
Makita Cordless Drill AD01 User Manual
Memorex Microcassette Recorder MB2186 User Manual
Merco Savory Toaster BG 1T User Manual
Metra Electronics Car Stereo System 99 7425 User Manual
Midland Radio Two Way Radio BR777 User Manual