Morphy Richards 28022 User Manual

Illustration  
13  
12 11  
14  
10  
2 Band Alarm  
Clock Radio  
15  
1
9
8
2
3
7
6
5
4
Location of controls  
9
Hour button  
1
2
3
4
5
6
7
8
Function selector switch  
PM indicator  
Alarm indicator  
Dial scale and pointer  
Tuning control  
Band selector switch AM/FM  
Buzzer/Volumecontrol  
Minute button  
10 FM wire aerial  
11 Time button  
12 Sleep button  
13 Alarm button  
14 Snoozebutton  
15 Battery compartment  
(located underneath unit)  
28009 / 28022 OPERATING INSTRUCTIONS  
P.2  
Electrical requirements  
Switching on and setting the clock time  
Check that the voltage on the rating plate of your clock radio corresponds  
with your house electricity supply which must be A.C. (Alternating current).  
Before any alarm functions can be used, you must set the clock to the correct time.  
1
Place the unit on a flat surface. Plug the mains plug into the wall socket  
and switch on the wall socket  
For clock radios with fitted plug.  
If the socket outlets in your home are not suitable for the plug supplied  
with this appliance the plug should be removed and the appropriate one  
fitted.  
2
3
The LED clock display will flash.  
Press and hold the TIME button (11) and simultaneously hold down the  
HOUR button (9) or the MINUTE button (8). The LED clock display will  
fast forward the minutes and hour segments. Release the TIME button (11)  
when your desired time is set.  
IMP0RTANT : THE PLUG REMOVED FROM THE MAINS LEAD, IF SEVERED, MUST  
BE DESTROYED AS A PLUG WITH A BARED FLEXIBLE CORD IS  
HAZARDOUS IF ENGAGED INTO A LIVE SOCKET OUTLET.  
4
The PM indicator (2) will illuminate to indicate 12.00 midday has been  
reached.  
Should the fuse in the 13 amp mains plug require changing a 3 amp BS1362  
fuse must be fitted.  
The socket outlet should be installed near the equipment and shall be easily  
accessible.  
Radio operation  
FM wire aerial  
Battery back-up facility (unit will work without a battery being fitted)  
Your alarm clock radio is equipped with a battery back-up facility.  
To obtain the maximum FM reception fully extend the wire FM aerial (10) (which  
is located at the rear of the unit) and alter the direction of the wire for best  
results.  
1
2
3
Remove the battery compartment cover (located underneath the unit) by  
pushing in the clip and lifting off.  
Insert a battery size 9 volts PP3/6LR61 and connect to terminals (Ensure  
batteries are inserted correctly)  
The aerial for the AM waveband is located inside the unit. To obtain the maximum  
AM reception rotate the clock radio.  
Replace the battery compartment cover.  
1
2
3
Slide the FUNCTION SELECTOR switch (1) to the ‘ON’ position.  
Adjust the VOLUME control (7) to a suitable level.  
Should a power interruption occur the clock will continue to run, however, time  
keeping will not be accurate. The display will be extinguished to conserve battery  
life but the memory will retain details of the clock time and alarm settings.  
Set the BAND SELECTOR switch (6) to either AM or FM as  
desired.  
If the optional battery is not installed in case of the AC power failure the display  
will blink to indicate the power was interrupted. You will need to reset the clock  
and alarm.  
Battery back-up is designed to operate for a short period only.  
If the unit is not to be used for a prolonged period, remove the battery to  
avoid battery leakage.  
4
5
Slowly adjust the TUNING control (5) to select your desired station.  
To switch off the radio, slide the FUNCTION SELECTOR  
switch (1) to the ‘OFF’ position.  
In the interests of environmental safety : dispose of batteries safely.  
P.3  
P.4  

Lenovo 2565 User Manual
KitchenAid Coffeemaker 253 User Manual
JVC KD G117 User Manual
iSymphony CR3 User Manual
Grindmaster P200E User Manual
Fujitsu Computer Drive MBB2147RC User Manual
Cypress Quad HOTLink II CYV15G0404RB User Manual
Chauvet LEGEND 550 User Manual
Bunn VP17 2 User Manual
AT&T MOTO Z9 User Manual